Zmiana hasła sieci bezprzewodowej

Aby zmienić hasło w Cisco 1941, wykonaj następujące kroki (wzięte z tego źródła ):

Podłącz router (przez port konsoli) do komputera i uruchom emulator terminala z następującymi ustawieniami:

9600 bodów

Brak parzystości

8 bitów danych

1 bit stopu

Brak kontroli przepływu

Jeśli udało Ci się uzyskać dostęp do routera, wpisz w wierszu polecenia show version i zapisz ustawienia rejestru konfiguracji. (Przykładowy przykład resetowania całego hasła jest poniżej, wykonywany za pomocą routera 2900, ale ma tę samą procedurę (źródło to ta sama strona))

Wyłącz router i włącz go ponownie.

Naciśnij klawisz Break na klawiaturze terminala, aż zobaczysz, że router jest w trybie ROMMON.

Wpisz „confreg 0x2142” i naciśnij enter w wyświetlonym pytaniu rommon 1>.

Wpisz „reset” i naciśnij enter w wyświetlonym monicie rommon 2>.

Wpisz „nie” po każdym pytaniu konfiguracyjnym i naciśnij klawisz Enter lub naciśnij Ctrl + C dla każdego pytania, aby pominąć konfigurację.

Wpisz „enable” i naciśnij klawisz Enter po wyświetleniu Router>monitu.

Powinieneś teraz zobaczyć monit Router#.

Wpisz „config memory” lub ( dokładnie ) „copy startup-config running-config”, a następnie naciśnij Enter.

Spowoduje to skopiowanie pamięci NVRAM do pamięci.

Teraz wpisz „configure terminal” i wciśnij enter.

Podpowiedź terminalu powinna być teraz hostname(config)#.

Wpisz „włącz sekret” (pamiętaj spację!) I wpisz nowe hasło.

Dla każdego interfejsu, którego użyjesz, ustaw pozycję, wpisując nazwę interfejsu w konsoli, następnie naciśnij Enter, następnie wpisz „no shutdown” i wciśnij Enter. (w razie wątpliwości najpierw sprawdź)

Aby zobaczyć listę dostępnych interfejsów (specjalnie do wyszukiwania ich nazw), wpisz „show ip interface brief” i naciśnij enter.

Kiedy skończysz konfigurować pożądane interfejsy, wpisz „config-register” + wartość, którą zapisałeś na początku (jeśli straciłeś tę wartość, możesz bezpiecznie wpisać 0x2102).

Wpisz „end” i naciśnij enter po wyświetleniu monitu.

Pytanie powinno być teraz hostname#.

Wpisz „write memory” lub „copy running-config startup-config”, aby zatwierdzić zmiany.

Nie wygląda na to, że istnieje sposób na zmianę hasła do konkretnego modemu. Uważam, że modem nie ma żadnego wpływu na bezpieczeństwo transmisji twojego Wi-Fi, więc to powinno wystarczyć.

(przykład wspomniany powyżej, poniżej)

Router>enable
Password:
Password:
Password:
% Bad secrets

Router>show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, 
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command


This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
[email protected].

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Technology Package License Information for Module:'c2900'

----------------------------------------------------------------
Technology    Technology-package          Technology-package
              Current       Type          Next reboot
-----------------------------------------------------------------
ipbase        ipbasek9      Permanent     ipbasek9
security      securityk9    Permanent     securityk9
uc            uck9          Permanent     uck9
data          datak9        Permanent     datak9

Configuration register is 0x2102


Router>



!--- The router was just powercycled, and during bootup a
!--- break sequence was sent to the router after seeing the following message
!--- program load complete, entry point: 0x80008000, size: 0x6fdb4c.


!

rommon 1 > confreg 0x2142

You must reset or power cycle for new config to take effect

rommon 2 > reset

System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)
Copyright (c) 2009 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
C2900 platform with 524288 Kbytes of main memory


program load complete, entry point: 0x80008000, size: 0x6fdb4c

Self decompressing the image : ###############################
##############################################################
##############################################################
##############################################################
############################### [OK]


 Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

 cisco Systems, Inc.
 170 West Tasman Drive
 San Jose, California 95134-1706

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)


 --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

00:00:19: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Ethernet0/1, changed state to up
00:00:19: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
00:00:19: %LINK-3-UPDOWN: Interface Serial0/1, changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, 
changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0,
 changed state to up
Router>
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, 
changed state to up
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, 
changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, 
changed state to down
00:00:50: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team
00:00:50: %LINK-5-CHANGED: Interface BRI0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Ethernet0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Serial0/0, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Ethernet0/1, 
changed state to administratively down
00:00:52: %LINK-5-CHANGED: Interface Serial0/1, 
changed state to administratively down
00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, 
changed state to down
00:00:53: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/1, 
changed state to down
Router>
Router>enable
Router#copy startup-config running-config
Destination filename [running-config]?
1324 bytes copied in 2.35 secs (662 bytes/sec)
Router#
00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, 
changed state to down
00:01:24: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, 
changed state to down
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret < password >
Router(config)#^Z
00:01:54: %SYS-5-CONFIG_I: Configured from console by console
Router#show ip interface brief

Interface   IP-Address        OK?  Method     Status                   Protocol
Ethernet0/0 10.200.40.37      YES  TFTP       administratively down    down
Serial0/0   unassigned        YES  TFTP       administratively down    down
BRI0/0      193.251.121.157   YES  unset      administratively down    down
BRI0/0:1    unassigned        YES  unset      administratively down    down
BRI0/0:2    unassigned        YES  unset      administratively down    down
Ethernet0/1 unassigned        YES  TFTP       administratively down    down
Serial0/1   unassigned        YES  TFTP       administratively down    down
Loopback0   193.251.121.157   YES  TFTP       up                       up
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface Ethernet0/0
Router(config-if)#no shutdown
Router(config-if)#
00:02:14: %LINK-3-UPDOWN: Interface Ethernet0/0, changed state to up
00:02:15: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0, 
changed state to up
Router(config-if)#interface BRI0/0
Router(config-if)#no shutdown
Router(config-if)#
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down
00:02:26: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up
00:02:115964116991: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0, 
TEI 68 changed to up
Router(config-if)#exit
Router#
00:02:35: %SYS-5-CONFIG_I: Configured from console by console
Router#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Configuration register is 0x2102

Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#config-register 0x2102
Router(config)#^Z
00:03:20: %SYS-5-CONFIG_I: Configured from console by console

Router#show version
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1,
     RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 15:23 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M1, RELEASE SOFTWARE (fc1)

c2921-CCP-1-xfr uptime is 2 weeks, 22 hours, 15 minutes
System returned to ROM by reload at 06:06:52 PCTime Mon Apr 2 1900
System restarted at 06:08:03 PCTime Mon Apr 2 1900
System image file is "flash:c2900-universalk9-mz.SPA.150-1.M1.bin"
Last reload reason: Reload Command

Cisco CISCO2921/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FHH1230P04Y
1 DSL controller
3 Gigabit Ethernet interfaces
9 terminal lines
1 Virtual Private Network (VPN) Module
1 Cable Modem interface
1 cisco Integrated Service Engine-2(s)
   Cisco Foundation 2.2.1 in slot 1
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
248472K bytes of ATA System CompactFlash 0 (Read/Write)
62720K bytes of ATA CompactFlash 1 (Read/Write)

Configuration register is 0x2142 (will be 0x2102 at next reload)

Router#

Addison Crump
źródło

... do którego routera lub modemu to dotyczy? Jaki model?

Darth Android

Ach - wierzę, że źle zrozumiałem pytanie. Odpowiedziałem, przyjmując modem Cisco, ponieważ proces ten dotyczy tylko takich. Z jakiego modemu korzystasz, @ss_millionaire? (Ta metoda dotyczy wszystkich współczesnych routerów cisco.)

Addison Crump,

@VTCAKAVSMoACE Używam routera Cisco 1941, ale modem nie jest modemem Cisco. To jest Huawei.

ss_millionaire,

@ss_millionaire Jaki posiadasz model modemu Huawei i jakiego urządzenia używasz obecnie do łączenia się z Internetem? (jak w routerze czy modemie?)

Addison Crump

Modem to Huawei HG8245A. Nie rozumiem, co rozumiesz przez hasło urządzenia, którego używam do łączenia się z Internetem. Myślę, że hasło jest niezależne od obu urządzeń, ponieważ wszystkie trzy hasła są różne czy się mylę?

ss_millionaire,

Zmiana hasła sieci bezprzewodowej

Odpowiedzi: